Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterFast, Reliable Door Installation Across San Bruno
Door installation in San Bruno runs $650-$2,900 for most entry and swing doors, while full-frame replacements on older tract homes with STC-rated glazing for FAA noise zones typically land between $2,400 and $5,800. We serve every San Bruno ZIP code, from Crestmoor to the flatlands east of El Camino Real, and our crews know what these houses look like behind the old doorframe. Call (888) 635-0804 for a free, no-surprise estimate.
Most homes in San Bruno were built between the late 1940s and early 1960s. They carry original steel or aluminum entry doors in frames that were never designed for acoustic performance or modern pre-hung units. When we remove a 1950s door on a San Bruno tract home, we’re usually not just swapping the slab. We’re resolving framing that’s undersized, weather-stripping that’s failed from wind-driven fog, and waterproofing that never worked. Our Door Installation team is built for exactly this kind of work. So here’s what you should expect.
Why TruePane Windows & Doors Is San Bruno’s Preferred Door Installation Company
San Bruno sits directly under SFO’s primary approach and departure corridors. That is not a real estate footnote; it rewrites the technical specification for every exterior door on a house. Many blocks here fall inside FAA Part 150 noise-eligible zones, which means a door replacement can qualify for federal reimbursement if, and only if, the glazing meets STC 35-40 requirements and comes from a program-approved manufacturer line. Our team verifies the STC rating against the homeowner’s noise study before we order a single unit. That’s the kind of detail a generalist installer may skip, and it’s the kind of detail that costs you the reimbursement.
We’re led by Dale Kessler, a second-generation glazier who started TruePane in 2008 because he had seen too many out-of-true installs and voided warranty claims on Peninsula homes. Since then, we’ve built our San Bruno reputation the way a tradesman builds it: by returning to the same neighborhoods, fixing what we installed five or ten years ago, and answering the phone when a homeowner notices a draft. A live person answers our calls 24/7. Not a voicemail tree, not a call center. Every job carries the Done Right Promise and The Keystone Standard: both manufacturer warranty layers are registered in writing, with durations stated, before the truck leaves your driveway.
Our Door Installation Services in San Bruno
Entry & Swing Doors
This is the work we do most often in San Bruno because the housing stock demands it. Original 1950s steel frames in Crestmoor, Rollingwood, and the flatlands east of El Camino Real are routinely undersized for modern pre-hung units. That means a straight slab swap is rarely the right answer. We frame the opening correctly, set the sill on flashing tape that won’t rot from fog-driven moisture, and hang a door that opens square in July and January. Entry and swing door installs in San Bruno typically run $650-$2,900 depending on frame condition and glazing spec.
Double & French Doors
Double and French doors on a San Bruno home carry a specific liability: wind. The San Bruno Gap funnels Pacific wind directly into residential streets, so two-panel door systems need astragals, thresholds, and weather-stripping spec’d for real wind loading. We’ve seen doors that bind within one fog season because the header settled and the panels drifted. Our crew checks the header before setting the unit, not after. Double and French door installs typically run $1,800-$5,200 depending on the opening and the glazing package.
Bifold & Folding Doors
Sliding & Patio Doors in San Bruno and folding systems go wrong when the track is out of level by even a quarter inch. On San Bruno post-war tract homes, that can happen because the subfloor has moved over seventy years. We install these systems with adjustable track hardware and we don’t leave the job until the panels slide without binding. Wide-opening folding door installs generally run $2,800-$7,500 depending on panel count and frame work.
Pivot Doors
A pivot door is a heavy, beautiful piece of hardware that punishes sloppy framing. Because many San Bruno homes sit on hillsides in Crestmoor, we see sloped floors more often than flat ones. Pivot doors require dead-level thresholds and a top pivot that is perfectly plumb to the bottom. When the floor is out of level, we shim and re-frame before we ever hang the slab. Pivot door installs in San Bruno typically run $2,200-$6,800.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in San Bruno
We install and service doors from PGT, CGI, and CWS, among other manufacturer lines. Those are three names that show up in FAA Part 150 filings and coastal wind-zone specs. We carry much of the hardware and seal stock these units require, so turnaround on San Bruno service calls runs short. If a PGT or CGI door fails in a fog belt, we don’t need to wait on a regional warehouse. We carry the parts, and we know the install.
Common Door Installation Problems We See in San Bruno Homes
- FAA reimbursement stalls on the glazing spec. The replacement door’s glass package doesn’t match the noise study on file with the airport authority. You submit the claim, the airport denies it, and you’re left holding the full bill. We verify STC before ordering so the reimbursement doesn’t die on paperwork.
- Undersized original jamb framing. 1950s steel door frames in flatland tract homes weren’t built for modern pre-hung units. After demo, the opening is too narrow, the header is weak, and the rough framing needs reconstruction. A quote that doesn’t anticipate this will change once the wall is open.
- Wind-driven fog rot at the sill. The San Bruno Gap pushes marine fog sideways into door sills. If the installer didn’t tape-flash under the threshold, moisture moves into the jamb and subfloor within a few seasons. By the time you see it, the rot is already in the framing.
- Seal failure on insulated glass near the marine layer. Constant fog and salt air shorten the life of low-quality insulated glass. We spec laminated low-E with argon fill for San Bruno homes precisely to keep the seal intact longer than a budget glazing package would.
Pricing for Door Installation in San Bruno, CA
Here’s what you’re actually looking at in San Bruno. A basic entry door slab swap runs $650-$1,400. A full-frame entry door replacement with new rough framing, flashing, and a standard insulated glass unit runs $1,900-$3,500. If you’re in an FAA Part 150 zone and need STC 35-40 rated glass from a program-approved manufacturer, plan on $2,400-$5,800. Double and French doors run $1,800-$5,200. Pivot doors run $2,200-$6,800. Arched and custom doors run higher because the unit itself is built to your opening, and we may need to modify framing. The variables are framing condition, glazing spec, and whether the subfloor needs leveling. None of these numbers should surprise you on the bill. We write the allowance into the contract, and if we uncover something behind the wall, you see the price in writing before we touch it. Call (888) 635-0804 for a free estimate.
| Door Type | Typical San Bruno Range |
|---|---|
| Entry / Swing Door (slab swap) | $650 - $1,400 |
| Entry / Swing Door (full frame, STC rated) | $2,400 - $5,800 |
| Double / French Doors | $1,800 - $5,200 |
| Pivot Door | $2,200 - $6,800 |
| Storm Door | $550 - $1,300 |
We Also Serve Cities Near San Bruno
TruePane runs crews into Millbrae, South San Francisco, Pacifica, and Daly City. If you’re just over the San Bruno line and you’re dealing with the same fog-belt conditions we see in Crestmoor, give us a call. Our San Bruno customers know the drill: free estimate, line-item quote, and a door that swings right the first time.
Serving San Bruno, CA - Our Local Coverage Area
We’re based in the San Bruno area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Door Installation in San Bruno
You can check the San Francisco International Airport Part 150 noise compatibility maps, which plot eligible residential blocks by noise contour. If your home on 94066 falls inside the eligible contour, your door replacement may qualify for reimbursement when the exterior glazing meets STC 35-40 and the manufacturer is on the approved list. Call (888) 635-0804 and we can check the spec against your address before you order anything.
Crestmoor homes are 1950s hillside tract construction, and after demo we frequently find the original jamb framing undersized or water-rotted from fog-driven moisture. The quote comes in at a straight replacement, we open the wall, and the framing needs reconstruction before a pre-hung unit will sit square. That work is real and extra. We write framing allowances into every San Bruno contract so the price doesn’t move without your written approval.
Yes. Impact Windows & Doors - San Bruno options are not restricted to wind-borne debris zones. A PGT or CGI impact-rated unit is overkill for San Bruno wind loading, but it will close tightly against the Gap wind and it carries better seal longevity in the marine layer. You pay more for the door itself. That’s the trade. Call (888) 635-0804 and we can price both options side by side on paper.
Yes, San Bruno’s combination of constant marine fog, wind, and salt air is hard on budget insulated glass seals. The fix is specification, not luck: Energy-Efficient Windows - San Bruno options with laminated low-E glass and argon fill hold their seal longer in a fog belt. We spec that as standard on exterior doors in San Bruno, not as an upsell. If a seal fails inside our warranty window, the fix is covered.
If the installed unit fails the airport authority’s inspection because the STC rating or manufacturer doesn’t match the noise study, the reimbursement is denied and you own the cost. That’s why we verify the spec against your paperwork before ordering, and why our installers document the STC rating at completion. If the work is wrong, the Done Right Promise applies: we make it right, no arguing. Call (888) 635-0804 and we’ll review your Part 150 paperwork with you.
Written by Dale Kessler, Owner at TruePane Windows & Doors, serving San Bruno and the greater Peninsula. If the pane is not true, the job is not done.